rear main shaft是什么意思 rear main shaft的中文翻译、读音、例句

rear main shaft通常被翻译为”后主轴”的意思，还有后主轴的意思，发音是[rearmainshaft]，rear main shaft来源于英语，在《荷林斯英英小词典》中，共找到36个与rear main shaft相关的例句。

Rear main shaft的中文翻译

1.后主轴

例句:The opposite direction airflow in Eastern Main Shaft of Certain Mine is caused by the main fan stoping work to undergo repair. (某矿东主井因停产检修、主扇停运引起了主井风流反向。)

用法及短语

rear main shaft一般作为名词使用，如在rear shaft(后轴)、main shaft([机] 主轴, 总轴)、rear axle shaft(后轮[后桥]轴)等常见短语中出现较多。

例句

1. (man over PA) Dr Nasch, please come to main reception. (翻译:please come to main reception.)

2. The vault room is located through a shaft on the east wall, 67 feet below the main level. (翻译:保险库位于东墙的竖井底部 主平面下方67英尺)

3. I took a bus to Main Street and I bought cloth for a dress. (翻译:I took a bus to Main Street and I bought cloth for a dress.)

4. They exit through the rear. (翻译:它们一路通向后面 They exit through the rear.)

5. Also to have independent thrusting from the main forward prolusion engine mounted in the rear of the VERT-LEV. (翻译:也有独立于主发动机向前冲式预演在垂直后方轻型电动车。)

6. To simulate combined testing for all of the important bearings on aviation engine main shaft, a shafting bearing tester is designed. (翻译:为模拟航空发动机主轴轴系所有重要轴承联合试验，研制了航空发动机轴系轴承试验机。)

7. The rear and front main jacks supply the required support of the MSS during concreting. (翻译:前后主千斤顶系统在浇注混凝土过程中支撑MSS。)

8. Remove cardan shaft from rear axle differential and tie it up. (翻译:从后轴差速器上拆下万向节轴并将其绑紧。)

9. Face the front of the vehicle, walk backwards towards the rear. (翻译:walk backwards towards the rear. {\r\fnArial\fs16\1cHFF8080})

10. I want you to shake your tail feathers down here ASAP, you dig? (翻译:This is your main man N. K. E.)

11. Sparated Bearing block for main transmission shaft Easy for maintenance and fix. (翻译:半精加工的主轴承安装后需要修整和调配，这样曲轴就必须拆下。)

12. There are two INI sections: [main] and [users]. (翻译:有两个INI段落：[main]和[users]。)

13. It is actually a 3mm collar which can be fit into the main shaft. (翻译:它实际上是一3毫米衣领可融入主井。)

14. We use belt or cogwheel to regulate speed for the main shaft , ball lead screw and stepping motor for operating plat form . (翻译:主轴采用皮带或齿轮变速，工作台采用滚珠丝杆，步进电机； )

15. On this basis, the basic model of main-shaft-less concave printer and ADRC are combined to get a new control algorithm. (翻译:在此基础上又将推导出的无主轴凹印机粗基本模型与AD – RC相结合，得出新的控制算法。)